Current Issue : October-December Volume : 2024 Issue Number : 4 Articles : 5 Articles
The usage of copper (Cu) ores containing low or no arsenic (As) has reduced, and Cu ores containing high levels of As have emerged as vital mineral resources for Cu extraction and processing. The quality of the Cu ores has decreased from 1.6% to approximately 1.0%. The proportion of As to Cu in 15% of Cu resources currently reaches 1:5. However, during the extraction and processing of Cu ores, As presents significant environmental harm. Hence, safely and effectively removing As is paramount in Cu smelting and processing, holding substantial importance in fostering environmentally sustainable practices within the Cu extraction and processing industry. This article consolidates the resource distribution of As-containing Cu (ACC) ores, comprehensively and systematically evaluates the present advancements in extracting techniques for these minerals, and identifies the challenges inherent in pyrometallurgical and wet processes for treating ACC deposits. Pyrometallurgy is a simple primary roasting technique and has widespread applicability in the treatment of various ACC minerals. Its disadvantages are the emission of exhaust gas and the high treatment costs associated with it. The wet arsenic removal method boasts advantages including minimal air pollution and a high resource recovery rate, significantly aiding in Cu concentrate recovery; its major drawback is the production of As-containing wastewater. The hydrometallurgical removal of As from ACC mines involves extracting As through leaching. Recently, biometallurgy has presented innovative solutions using specialized microorganisms to bioleach or bioabsorb As, but large-scale industrial applications still lack specific practical implementation. This review explores the underlying causes of the challenges encountered in processing ACC minerals. Additionally, it highlights pyrometallurgical roasting coupled with high-temperature filtration as a pivotal advancement in the extraction and processing of ACC ores....
A straightforward, fast and efficient analytical method was developed which utilizes a magnetic composite called three-dimensional graphene (3D-G@Fe3O4) as an adsorbent to recover nitrite ions (NO2 −) from environmental water samples. The investigation into the synthesized adsorbent contained an examination of its morphology, chemical composition, structural attributes, and magnetic properties. This comprehensive analysis was conducted using various instrumental techniques, including Fourier transform-infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), Raman spectroscopy, X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), Barrett-Joyner- Halenda (BJH), and vibrating sample magnetometry (VSM). The adsorbent surface was activated by adding cetyltrimethylammonium bromide (CTAB) to the sample solution. To improve the selectivity and sensitivity of the method, nitrite ions were reacted with sulfanilic acid and chromotropic acid sequentially. An orange-red azo-dye complex was formed in the presence of nitrite ions with a clear absorbance peak at 514 nm. The effect of the main experimental parameters such as the pH of the sample solution, adsorbent dosage, and CTAB dosage was explored, and the optimization process was performed using a central composite design (CCD). The linear dynamic range (20–100 ng mL−1) was determined under optimal experimental circumstances, yielding a reasonable determination coefficient (R2, 0.9993), a detection limit of 5.12 ng mL−1, an enrichment factor of 167, and precision values of 1.0% intraday and 2.9% inter-day. The methodology successfully identified minute nitrite ions in environmental water samples with relative recoveries that varied between 96.05 and 101.6 ng mL−1....
This paper presents original results from the unique analysis of the porous structure of activated carbons (ACs) produced through the chemical activation of polyethylene terephthalate (PET) and polyacrylonitrile (PAN), as well as from a physical mixture of both polymers. An advanced method of adsorbent surface analysis—more specifically, the new method of numerical clusteringbased adsorption analysis regarding the surface heterogeneity, pore geometry and adsorption energy distribution parameters—allowed us to obtain information about the porous structure of the ACs from the synthetic polymers mentioned above. As the results showed, ACs obtained with PAN were characterised by a first adsorbed layer with the highest volume. When the surface heterogeneity, highly desirable in most advanced adsorption processes, is taken into account, the materials with the best surface properties in both potassium carbonate (K2CO3) and potassium hydroxide (KOH) activation processes were the ACs obtained with a mass proportion of PET to PAN of 1:3, which were characterised by a low degree of surface heterogeneity and a first adsorbed layer presenting a relatively large volume....
Functionalization by noble metal catalysts and the construction of heterojunctions are two effective methods to enhance the gas sensing performance of metal oxide-based sensors. In this work, we adopt the porous ZIF-8 as a catalyst substrate to encapsulate the ultra-small Pt nanoparticles. The Pt/ZnO-In2O3 hollow nanofibers derived from Pt/ZIF-8 were prepared by a facile electrospinning method. The 25PtZI HNFs sensor possessed a response value of 48.3 to 100 ppm HCHO, 2.7 times higher than the pristine In2O3, along with rapid response/recovery time (5/22 s), and lower theoretical detection limit (74.6 ppb). The improved sensing properties can be attributed to the synergistic effects of electron sensitization effects and catalytic effects of Pt nanoparticles, and the high surface O− absorbing capability of heterojunctions. The present study paves a new way to design high performance formaldehyde gas sensors in practical application....
Because of their high mixing entropies, multi-component alloys can exhibit enhanced catalytic activity compared to traditional catalysts in various chemical reactions, including hydrogenation, oxidation, and reduction processes. In this work, new AgCoCuFeNi high entropy alloy nanoparticles were synthesized by the hydrogen reduction-assisted ultrasonic spray pyrolysis method. The aim was to investigate the effects of processing parameters (reaction temperature, precursor solution concentration, and residence time) on the microstructure, composition, and crystallinity of the high entropy alloy nanoparticles. The characterization was performed with scanning electron microscope, energy-dispersive X-ray spectroscopy, and X-ray diffraction. The syntheses performed at 600, 700, 800, and 900 ◦C, resulted in smaller and smoother spherical particles with a near-equiatomic elemental composition as the temperature increased to 900 ◦C.With 0.25, 0.1, and 0.05 M precursor solutions, narrower size distribution and uniform AgCoCuFeNi nanoparticles were produced by reducing the solution concentration to 0.05 M. A near-equiatomic elemental composition was only obtained at 0.25 and 0.05 M. Increasing the residence time from 5.3 to 23.8 s resulted in an unclear particle microstructure. None of the five metal elements were formed in the large tubular reactor. X-ray diffraction revealed that various crystal phase structures were obtained in the synthesized AgCoCuFeNi particles....
Loading....