Current Issue : October-December Volume : 2021 Issue Number : 4 Articles : 5 Articles
In this work, the modulational instability of dust-acoustic (DA) waves (DAWs) is theoretically studied in a four-component plasma medium with electrons, positrons, ions, and negative dust grains. The nonlinear and dispersive coefficients of the nonlinear Schrödinger equation (NLSE) are used to recognize the stable and unstable parametric regimes of the DAWs. It can be seen from the numerical analysis that the amplitude of the DA rogue waves decreases with increasing populations of positrons and ions. It is also observed that the direction of the variation of the critical wave number is independent (dependent) of the sign (magnitude) of q. The applications of the outcomes from the present investigation are briefly addressed....
When a longitudinal wave passes through a contact interface, second harmonic components are generated due to contact acoustic nonlinearity (CAN). The magnitude of the generated second harmonic is related to the contact state of the interface, of which a model has been developed using linear and nonlinear interfacial stiffness. However, this model has not been sufficiently verified experimentally for the case where the interface has a rough surface. The present study verifies this model through experiments using rough interfaces. To do this, four sets of specimens with different interface roughness values (Ra = 0.179 to 4.524 m) were tested; one set consists of two Al6061-T6 blocks facing each other. The second harmonic component of the transmitted signal was analyzed while pressing on both sides of the specimen set to change the contact state of the interface. The experimental results showed good agreement with the theoretical prediction on the rough interface. The magnitude of the second harmonic was maximized at a specific contact pressure. As the roughness of the contact surface increased, the second harmonic was maximized at a higher contact pressure. The location of this maximal point was consistent between experiments and theory. In this study, an FEM simulation was conducted in parallel and showed good agreement with the theoretical results. Thus, the developed FEM model allows parametric studies on various states of contact interfaces....
+is paper presents a method to predict the acoustic characteristics and steady-state responses of a flexible plate strongly coupled with rectangular cavity based on energy principle theory and Legendre polynomial series. First, the displacement of the plate and the sound pressure in the cavity are constructed in the form of two-dimensional and three-dimensional Legendre polynomial series, respectively. +e unknown expansion coefficients are obtained using the Rayleigh–Ritz technique based on the energy expressions for the strongly coupled plate-cavity system. +e accuracy, convergence, and efficiency of the present method are verified by comparing with the results available in the FEM and literature. Finally, the effects of the structural boundary conditions, cavity depth, and structural length-width ratio on the coupling natural frequency and the steady-state responses under three excitation conditions are analyzed....
Microphones have been extensively studied for many decades and their related theories are well-established. However, the physical presence of the sensor itself limits its practicality in many sound field control applications. Laser Doppler vibrometers (LDVs) are commonly used for the remote measurement of surface vibration that are related to the sound field without the introduction of any such physical intervention. This paper investigates the performance and challenges of using a piece of retro-reflective film directly as an acoustic membrane pick-up with an LDV to sense its vibration to form a remote acoustic sensing apparatus. Due to the special properties of the retroreflective material, the LDV beam can be projected to the target over a wide range of incident angles. Thus, the location of the LDV relative to the pick-up is not severely restricted. This is favourable in many acoustic sensing and control applications. Theoretical analysis and systematic experiments were conducted on the membrane to characterise its performance. One design has been selected for sensing sound pressure level above 20 dB and within the 200 Hz to 4 kHz frequency range. Two example applications—remote speech signal sensing/recording and an active noise control headrest—are presented to demonstrate the benefits of such a remote acoustic sensing apparatus with the retro-reflective material. Particularly, a significant 22.4 dB noise reduction ranging from 300 Hz to 6 kHz has been achieved using the demonstrated active control system. These results demonstrate the potential for such a solution with several key advantages in many applications over traditional microphones, primarily due to its minimal invasiveness....
Acoustic oscillation provides useful information regarding the interfacial coupling between metal transducer layers and substrate materials. The interfacial coupling can be significantly reduced by a mechanically soft layer between the transducer and substrate. However, preserving a thin, soft layer at the interface during fabrication is often challenging. In this study, we demonstrate that an amorphous CoB alloy on top of a sapphire substrate can substantially amplify acoustic oscillations. By analyzing the attenuation of acoustic oscillations, we show that a thin, soft layer with a thickness of >2 1 Å exists at the interface. The intermediate layer at the interface is further verified by investigating heat transport. By analyzing the slow decrease of the temperature of the transducer layer, we determine a thermal conductance of 35 5 MW m2 K1 at the transducer/substrate interface. This low value supports the existence of a thin, soft layer at the interface. Our results demonstrate that an amorphous metal with B alloying effectively preserves the soft nature at the interface and detects the acoustic propagation and heat transport across it....
Loading....